EZGO RXV 6" Spindle Lift Kit: Gas Cart Install Prep

By GOLFCARTSTUFF.COM™ | Golf Cart Wheels, Tires, Lights | Published: 2026-11-03

Category: 操作指南

Prep your 2014-2022 gas EZGO RXV for a Jake's 6" spindle lift kit: confirm fitment, gather tools, and follow a step-by-step install with checkpoints.

Quick answer

For a 2014-2022 gas EZGO RXV, the Jake's 6" spindle lift kit is a direct-fit option that raises ground clearance without changing the rear suspension design. Prep the cart on a level surface, confirm you have the right gas-model kit, and follow the steps below to install it safely.

Why the gas RXV needs its own kit

The EZGO RXV gas model from 2014-2022 has a different front suspension and steering layout than the electric RXV, so a kit listed for the electric cart will not fit. The Jake's 6" spindle lift for this application is built specifically for the newer gas RXV, and its ductile iron spindles are cast to be stronger than standard gray iron—a real advantage if you plan to run larger tires on rough ground.

Spindle lifts keep the original springs and shocks, so the ride quality stays close to stock. That makes this kit a good choice for trail riding and neighborhood cruising, but it is not a long-travel suspension. If you need maximum articulation for serious off-road use, an A-arm kit is the better tool.

What to check before you buy

Fitment is the most common reason a lift kit install goes wrong. Verify the cart is a gas RXV built between 2014 and 2022, and check that the kit part number matches Jake's #7505. Also confirm the wheel and tire package you plan to run—larger tires may require additional clearance or a different offset, and the catalog does not list a maximum tire size for this kit, so measure before you commit.

If your cart has worn front-end parts, address them first. A lift kit amplifies play in tie rods, bushings, and wheel bearings, so replacing worn components during the install saves a second teardown.

Step-by-step install prep and procedure

Park and secure the cart: Set the parking brake, chock the rear wheels, and lift the front end on a level, paved surface. Use jack stands rated for the cart's weight—never work under a cart supported only by a jack. A stable, level surface prevents the cart from shifting when you break loose the front suspension bolts.
Disconnect the battery: On a gas cart, disconnect the negative battery cable before you start turning wrenches near the engine bay or wiring. This is a quick step that prevents accidental sparks. Label the cable or take a photo before removal so reassembly is straightforward.
Remove the front wheels and stock spindles: Loosen the lug nuts before raising the cart, then remove the wheels. Separate the tie rod ends from the stock spindles using a tie rod puller, and keep the castle nuts and cotter pins organized by side. Do not hammer on the tie rod studs—use the correct puller to avoid damaging the threads.
Install the Jake's spindles: Bolt the new ductile iron spindles onto the cart's original steering knuckles following the kit instructions. Torque the mounting hardware to the specification in the Jake's manual, since the catalog does not list torque values. Recheck torque after the first 50 miles of driving, as new hardware can settle.
Reconnect the steering and check alignment: Reattach the tie rod ends to the new spindles, install new cotter pins, and set the front toe to the spec in the instructions. With the wheels on and the cart on the ground, bounce the front end and recheck toe before tightening the jam nuts. A quick tape-measure toe check at the tire tread saves a trip to the alignment shop.
Test-drive and re-torque: Lower the cart, reconnect the battery, and take a slow test drive in a safe area. Listen for clunks or rubbing, then recheck all fasteners and lug nut torque after the first short drive. If you hear a clunk over bumps, stop and inspect the spindle and tie rod hardware before driving further.

Product facts

EZGO RXV 6" Spindle Lift Kit (Gas, 2014-2022)⎮Jake's®: Jake's 6" spindle lift kit designed for 2014-2022 gas EZGO RXV carts, part #7505, with ductile iron spindles. The gas-specific fitment and stronger spindle material mean you can install it without adapting electric-cart parts, and it holds up better under larger tires.
EZGO RXV 6" Spindle Lift Kit (Gas, 2014-2022)⎮Jake's®